13.4.5 Packet Tracer – Troubleshoot WLAN Issues (Instructor Version) Addressing Table Device Interface IP Address Home Wireless Router Internet DHCP LAN 192.168.0.1 R1 G0/0/0.10 192.168.10.1/24 G0/0/0.20 192.168.20.1/24 G0/0/0.200 192.168.200.1/24 G0/0/1 172.31.1.1/24 SW1 VLAN 200 192.168.200.100/24 LAP-1 G0 DHCP WLC-1 Management 192.168.200.254/24 RADIUS Server NIC 172.31.1.254/24 Admin PC NIC 192.168.200.200/24 Web Server NIC 203.0.113.78/24 DNS Server NIC 10.100.100.254 Home Admin NIC DHCP Laptop NIC DHCP Laptop1 Wireless0 DHCP Laptop2 Wireless0 DHCP Tablet PC Wireless0 DHCP Smartphone Wireless0 DHCP WLAN Information WLAN SSID Authentication Username Password Home Network HomeSSID WPA2-Personal N/A Cisco123 WLAN VLAN10 SSID-10 WPA-2 PSK/Personal N/A Cisco123 WLAN VLAN 20…
Author: CCNA Exam Answers
13.3.12 Packet Tracer – Configure a WPA2 Enterprise WLAN on the WLC (Instructor Version) Addressing Table Device Interface IP Address R1 G0/0/0.5 192.168.5.1/24 G0/0/0.200 192.168.200.1/24 G0/0/1 172.31.1.1/24 SW1 VLAN 200 192.168.200.100/24 LAP-1 G0 DHCP WLC-1 Management 192.168.200.254/24 RADIUS/SNMP Server NIC 172.31.1.254/24 Admin PC NIC 192.168.200.200/24 Objectives In this activity, you will configure a new WLAN on a wireless LAN controller (WLC), including the VLAN interface that it will use. You will configure the WLAN to use a RADIUS server and WPA2-Enterprise to authenticate users. You will also configure the WLC to use an SNMP server. Configure a new VLAN interface…
13.2.7 Packet Tracer – Configure a Basic WLAN on the WLC (Instructor Version) Addressing Table Device Interface IP Address R-1 G/0/0 172.31.1.1/24 G0/0/1.5 192.168.5.1/24 G0/0/1.200 192.168.200.1/24 SW-1 VLAN 200 192.168.200.100/24 LAP-1 G0 DHCP WLC-1 Management 192.168.200.254/24 Server NIC 172.31.1.254/24 Admin PC NIC 192.168.200.200/24 Wireless Host Wireless NIC DHCP Objectives In this lab, you will explore some of the features of a wireless LAN controller. You will create a new WLAN on the controller and implement security on that LAN. Then you will configure a wireless host to connect to the new WLAN through an AP that is under the control…
13.1.10 Packet Tracer – Configure a Wireless Network (Instructor Version) Objectives Connect to a wireless router Configure the wireless router Connect a wired device to the wireless router Connect a wireless device to the wireless router Add an AP to the network to extend wireless coverage Update default router settings Introduction In this activity, you will configure a wireless router and an access point to accept wireless clients and route IP packets. Furthermore, you will also update some of the default settings. Instructions Part 1: Connect to a Wireless Router Step 1: Connect Admin to WR. a. Connect Admin to…
11.6.1 Packet Tracer – Switch Security Configuration (Instructor Version) VLAN Table Switch VLAN Number VLAN Name Port Membership Network SW-1 10 Admin F0/1, F0/2 192.168.10.0/24 20 Sales F0/10 192.168.20.0/24 99 Management F0/24 192.168.99.0/24 100 Native G0/1, G0/2 None 999 BlackHole All unused None SW-2 10 Admin F0/1, F0/22 192.168.10.0/24 20 Sales F0/10 192.168.20.0/24 99 Management F0/24 192.168.99.0/24 100 Native None None 999 BlackHole All unused None Objectives Part 1: Create a Secure Trunk Part 2: Secure Unused Switchports Part 3: Implement Port Security Part 4: Enable DHCP Snooping Part 5: Configure Rapid PVST PortFast and BPDU Guard Background You are…
11.1.10 Packet Tracer – Implement Port Security (Instructor Version) Addressing Table Device Interface IP Address Subnet Mask S1 VLAN 1 10.10.10.2 255.255.255.0 PC1 NIC 10.10.10.10 255.255.255.0 PC2 NIC 10.10.10.11 255.255.255.0 Rogue Laptop NIC 10.10.10.12 255.255.255.0 Objective Part 1: Configure Port Security Part 2: Verify Port Security Background In this activity, you will configure and verify port security on a switch. Port security allows you to restrict a port’s ingress traffic by limiting the MAC addresses that are allowed to send traffic into the port. Step 1: Configure Port Security a. Access the command line for S1 and enable port security…
9.3.3 Packet Tracer – HSRP Configuration Guide (Instructor Version) Addressing Table Device Interface IP Address Default Gateway R1 G0/0 10.1.1.1/30 N/A G0/1 192.168.1.1/24 G0/2 10.1.1.9/30 R2 G0/0 10.1.1.2/30 N/A G0/1 10.1.1.5/30 G0/2 10.100.100.1/30 R3 G0/0 192.168.1.3/24 N/A G0/1 10.1.1.6/30 G0/2 10.1.1.10/30 I-Net G0/1 10.100.100.2/30 N/A HSRP Virtual Gateway Virtual 192.168.1.254/24 N/A S1 VLAN 1 192.168.1.11/24 192.168.1.1 S3 VLAN 1 192.168.1.13/24 192.168.1.3 PC-A NIC 192.168.1.101/24 192.168.1.1 PC-B NIC 192.168.1.103/24 192.168.1.3 Web Server NIC 209.165.200.226/27 209.165.100.225 Note: The I-Net router is present in the internet cloud and cannot be accessed in this activity. Objectives In this Packet Tracer activity, you will learn…
7.4.1 Packet Tracer – Implement DHCPv4 (Instructor Version) Addressing Table Device Interface IPv4 Address Subnet Mask Default Gateway R1 G0/0 192.168.10.1 255.255.255.0 N/A S0/0/0 10.1.1.1 255.255.255.252 R2 G0/0 192.168.20.1 255.255.255.0 N/A G0/1 DHCP Assigned DHCP Assigned S0/0/0 10.1.1.2 255.255.255.252 S0/0/1 10.2.2.2 255.255.255.252 R3 G0/0 192.168.30.1 255.255.255.0 N/A S0/0/1 10.2.2.1 255.255.255.0 PC1 NIC DHCP Assigned DHCP Assigned DHCP Assigned PC2 NIC DHCP Assigned DHCP Assigned DHCP Assigned DNS Server NIC 192.168.20.254 255.255.255.0 192.168.20.1 Objectives Part 1: Configure a Router as a DHCP Server Part 2: Configure DHCP Relay Part 3: Configure a Router as a DHCP Client Scenario As the network…
7.2.10 Packet Tracer – Configure DHCPv4 (Instructor Version) Topology Addressing Table Device Interface IPv4 Address Subnet Mask Default Gateway R1 G0/0 192.168.10.1 255.255.255.0 N/A S0/0/0 10.1.1.1 255.255.255.252 N/A R2 G0/0 192.168.20.1 255.255.255.0 N/A G0/1 DHCP Assigned DHCP Assigned N/A S0/0/0 10.1.1.2 255.255.255.252 N/A S0/0/1 10.2.2.2 255.255.255.252 N/A R3 G0/0 192.168.30.1 255.255.255.0 N/A S0/0/1 10.2.2.1 255.255.255.0 N/A PC1 NIC DHCP Assigned DHCP Assigned DHCP Assigned PC2 NIC DHCP Assigned DHCP Assigned DHCP Assigned DNS Server NIC 192.168.20.254 255.255.255.0 192.168.20.1 Objectives Part 1: Configure a Router as a DHCP Server Part 2: Configure DHCP Relay Part 3: Configure a Router as a…
6.4.1 Packet Tracer – Implement EtherChannel (Instructor Version) Topology Objectives Part 1: Build the network Part 2: Configure EtherChannel Background You have been assigned the task of designing an EtherChannel implementation for a company that wants to improve the performance of their switch trunk links. You will try several different ways of implementing the EtherChannel links in order to evaluate which is the best for the company. You will build the topology, configure trunk ports, and implement LACP and PAgP EtherChannels. Instructions Part 1: Build the network. Use the table below to build the switch topology. Step 1: Obtain the…
6.3.4 Packet Tracer – Troubleshoot EtherChannel (Instructor Version) Objectives Part 1: Examine the Physical Layer and Correct Switch Port Mode Issues Part 2: Identify and Correct Port Channel Assignment Issues Part 3: Identify and Correct Port Channel Protocol Issues Background A junior technician recently configured four switches. Users are complaining that the network is running slowly, and they would like you to investigate. Port Channel Table Channel Group Ports Protocol 1 S1: G0/1, G0/2 S2: G0/1, G0/2 LACP active 2 S2: G0/1, G0/2 S4: G0/1, G0/2 LACP active 3 S1: F0/23, F0/24 S2: F0/23, F0/24 LACP active 4 S3: F0/23,…
6.2.4 Packet Tracer – Configure EtherChannel (Instructor Version) Objectives Part 1: Configure Basic Switch Settings Part 2: Configure an EtherChannel with Cisco PAgP Part 3: Configure an 802.3ad LACP EtherChannel Part 4: Configure a Redundant EtherChannel Link Background Three switches have just been installed. There are redundant uplinks between the switches. As configured, only one of these links can be used; otherwise, a bridging loop might occur. However, using only one link utilizes only half of the available bandwidth. EtherChannel allows up to eight redundant links to be bundled together into one logical link. In this lab, you will configure…