CCNA 3 Scaling Networks Ver 6.0 – ITN Final Test online

A network administrator is adding a new VLAN for testing. The company uses VTP and the VLAN is not directly attached to either of the switches configured as VTP servers. What is the best method to add this VLAN to the network?

Which industry-wide specification was developed to decrease the time that is needed to move to the forwarding state by switch ports that are operating in a redundantly switched topology?

Refer to the exhibit.
A network administrator is verifying the bridge ID and the status of this switch in the STP election. Which statement is correct based on the command output?

Refer to the exhibit.
Which switching technology would allow data to be transmitted over each access layer switch link and prevent the port from being blocked by spanning tree due to the redundant link?

Which three pairs of trunking modes will establish a functional trunk link between two Cisco switches?

(Choose three.)

Refer to the exhibit.
The configuration shows the commands entered by a network administrator for inter-VLAN routing. However, host PCA cannot communicate with PCB. Which part of the inter-VLAN configuration causes the problem?

Refer to the exhibit.
What is the role of the SW3 switch?

Refer to the exhibit.
What is the role of the SW3 switch?

Which routing protocol is able to scale for large networks and utilizes non-backbone areas for expansion?

In the Cisco hierarchical design model, which layer is more likely to have a fixed configuration switch than the other layers?

A network engineer is interested in obtaining specific information relevant to the operation of both distribution and access layer Cisco devices. Which command provides common information relevant to both types of devices?

A switched network has converged completely. All switches currently have a VTP revision number of 5. A new switch that has been configured as a VTP server is added to the network. The new switch has a VTP revision number of 4. What will occur within the network?

Which spanning tree standard was developed by Cisco to provide separate instances of 802.1w per VLAN?

What are two advantages of EtherChannel?

(Choose two.)

When EtherChannel is implemented, multiple physical interfaces are bundled into which type of logical connection?

When a range of ports is being configured for EtherChannel, which mode will configure LACP on a port only if the port receives LACP packets from another device?

A new chief information officer (CIO) has requested implementation of a link-state dynamic routing protocol. Which two routing protocols fulfill this requirement?

(Choose two.)

Refer to the exhibit. A network administrator is utilizing RIPv1 in the exhibited network topology. What would the router R2 do with a packet that is originating from the 192.168.4.0/24 network and destined for network 172.16.1.0/24?

What best describes the operation of distance vector routing protocols?

Which statement defines the speed of convergence of routing protocols?

What is associated with link-state routing protocols?

Which two pieces of information are contained within a link-state packet (LSP)?

(Choose two.)

What is a difference between the routing protocols EIGRP and OSPF?

What protocol is used by EIGRP for the delivery and receipt of EIGRP packets?

How is bandwidth to a destination network calculated by EIGRP?

Refer to the exhibit.
A network administrator has attempted to implement a default route from R1 to the ISP and propagate the default route to EIGRP neighbors. Remote connectivity from the EIGRP neighbor routers to the ISP connected to R1 is failing. Based on the output from the exhibit, what is the most likely cause of the problem?

Refer to the exhibit.
Which statement accurately reflects the configuration of routing on the HQ router?

Which command would limit the amount of bandwidth that is used by EIGRP for protocol control traffic to approximately 128 Kb/s on a 1.544 Mb/s link?

Which criterion is preferred by the router to choose a router ID?

What is the effect of entering the network 192.168.10.1 0.0.0.0 area 0 command in router configuration mode?

Which three requirements are necessary for two OSPFv2 routers to form an adjacency? (Choose three.)

Which type of OSPF router connects an OSPF area to non-OSPF routing domains?

Which function is performed by an OSPF ABR?

In which mode is the area area-id range address mask command issued when multiarea OSPF summarization is being configured?

Refer to the exhibit.
What are three resulting DR and DBR elections for the given topology?

(Choose three.)

Refer to the exhibit.
How did this router learn of the highlighted route in the routing table?

Which command can be used to view OSPF adjacencies with neighboring routers along with the transition state?

What is the term that is used for the area of a network that is affected when a device or network service experiences problems?

What term is used to express the thickness or height of a switch?

Which configuration changes will increment the configuration revision number on the VTP server?

What are three characteristics of VTP? (Choose three.)

What is the purpose of the vlan.dat file on a switch?

What eliminates switching loops?

A small company network has six interconnected Layer 2 switches. Currently all switches are using the default bridge priority value. Which value can be used to configure the bridge priority of one of the switches to ensure that it becomes the root bridge in this design?

What is the value used to determine which port on a non-root bridge will become a root port in a STP network?

Which three STP states were replaced with the RSTP discarding state? (Choose three.)

As the network administrator you have been asked to implement EtherChannel on the corporate network. What does this configuration consist of?

Which command will start the process to bundle two physical interfaces to create an EtherChannel group via LACP?

A network administrator configured an EtherChannel link with three interfaces between two switches. What is the result if one of the three interfaces is down?

When EtherChannel is configured, which mode will force an interface into a port channel without exchanging aggregation protocol packets?

Refer to the exhibit.
A network administrator is reviewing the configuration of switch S1. Which protocol has been implemented to group multiple physical ports into one logical link?