CCNA 3 Chapter 9 Exam Answers
-
Which characteristic describes both ABRs and ASBRs that are implemented in a multiarea OSPF network?
They are required to reload frequently and quickly in order to update the LSDB.
They both run multiple routing protocols simultaneously.
They are required to perform any summarization or redistribution tasks.*
They usually have many local networks attached.
-
What type of OSPF LSA is originated by ASBR routers to advertise external routes?
type 5*
type 2
type 3
type 1 -
What OSPF LSA type is used to inform routers of the router ID of the DR in each multiaccess network in an OSPF area?
type 3
type 2*
type 1
type 4 -
Refer to the exhibit. Which two statements are correct? (Choose two.)
To reach network 192.168.1.0, traffic will exit via the Serial0/0/0 interface.*
The entry for 172.16.200.1 represents a loopback interface.
To reach network 172.16.2.0, traffic will travel through the GigabitEthernet0/0 interface.
The routing table contains two intra-area routes.
The routing table contains routes from multiple areas.* -
What are two reasons for creating an OSPF network with multiple areas? (Choose two.)
to simplify configuration
to reduce SPF calculations*
to reduce use of memory and processor resources*
to provide areas in the network for routers that are not running OSPF
to ensure that an area is used to connect the network to the Internet
-
What is used to facilitate hierarchical routing in OSPF?
frequent SPF calculations
autosummarization
the election of designated routers
the use of multiple areas*
-
A network administrator is verifying a multi-area OSPF configuration by checking the routing table on a router in area 1. The administrator notices a route to a network that is connected to a router in area 2. Which code appears in front of this route in the routing table within area 1?
C
O
O IA*
O E2
-
Which two statements correctly describe OSPF type 3 LSAs? (Choose two.)
Type 3 LSAs are known as autonomous system external LSA entries.
Type 3 LSAs are known as router link entries.
Type 3 LSAs are used for routes to networks outside the OSPF autonomous system.
Type 3 LSAs are used to update routes between OSPF areas.*
Type 3 LSAs are generated without requiring a full SPF calculation.*
-
What routing table descriptor is used to identify OSPF summary networks that originate from an ABR?
O IA*
O E1
O E2
O -
Refer to the exhibit. What can be concluded about network 192.168.4.0 in the R2 routing table?
The network was learned through summary LSAs from an ABR.
The network can be reached through the GigabitEthernet0/0 interface.
The network was learned from a router within the same area as R2.*
This network should be used to forward traffic toward external networks. -
Which three steps in the design and implementation of a multiarea OSPF network are considered planning steps?
(Choose three.)
Troubleshoot the configurations.
Define the network requirements.*
Configure OSPF.
Gather the required parameters.*
Verify OSPF.
Define the OSPF parameters.* -
Which two networks are part of the summary route 192.168.32.0/22? (Choose two.)
192.168.35.0/24*
192.168.38.0/24
192.168.37.0/24
192.168.36.0/24
192.168.33.0/24*
192.168.31.0/24 -
Refer to the exhibit. What is indicated by the O IA in the router output?
The route was manually configured.
The route was learned from outside the internetwork.
The route was learned from within the area.
The route was learned from another area.* -
Refer to the exhibit. A network administrator has been asked to summarize the networks shown in the exhibit as part of a multiarea OSPF implementation. All addresses are using a subnet mask of 255.255.255.0. What is the correct summarization for these eight networks?
10.0.4.0 255.255.0.0
10.0.0.0 255.255.240.0*
10.0.4.0 255.255.248.0
10.0.8.0 255.255.248.0 -
The network administrator has been asked to summarize the routes for a new OSPF area. The networks to be summarized are 172.16.8.0, 172.16.10.0, and 172.16.12.0 with subnet masks of 255.255.255.0 for each network. Which command should the administrator use to forward the summary route for area 15 into area 0?
area 15 range 172.16.8.0 255.255.255.248
area 0 range 172.16.8.0 255.255.255.248
area 0 range 172.16.8.0 255.255.248.0
area 15 range 172.16.8.0 255.255.248.0* -
Question as presented:
-
Fill in the blank. Do not use acronyms.
OSPF type 2 LSA messages are only generated by the ______ router to advertise routes in multiaccess networks.
Correct Answer: designated*
-
Fill in the blank. Use a number.
An ASBR generates type ________ LSAs for each of its external routes and floods them into the area that it is connected to.
Correct Answer: 5* -
Fill in the blank. Use a number.
A type ___________ LSA identifies the ASBR and provides a route to it.
Correct Answer: 4* -
Refer to the exhibit. Fill in the blank. Do not use abbreviations.
The ____________ command must be issued to configure R1 for multiarea OSPF.
Correct Answer: network 192.168.10.128 0.0.0.127 area 1* -
Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
Why are users in the OSPF network not able to access the Internet?The default route is not redistributed correctly from router R1 by OSPF.
The network statement is misconfigured on router R1.*
The OSPF network statements are misconfigured on routers R2 and R3.
The OSPF timers that are configured on routers R1, R2, and R3 are not compatible.
The interface that is connected to the ISP router is down. -
Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
Fill in the blank. Do not use abbreviations.
What is the missing command on router R2 to establish an adjacency between routers R1 and R3?Correct Answer: network 172.16.10.0 0.0.0.255 area 0*
all the fill in the blank answers were wrong..i dont know their is a cisco software problem or your answers ware wrong