CCNA 3 Scaling Networks Ver 6.0 – ITN Chapter 6 Exam Answers

CCNA 3 Scaling Networks Ver 6.0 – ITN Chapter 6 Exam Answers
Rate this post
  1. What information does EIGRP maintain within the routing table?

    only successors*

    all routes known to the router

    only feasible successors

    both successors and feasible successors

    adjacent neighbors

  2. Which configuration is necessary to ensure successful operation of EIGRP for IPv6?

    The eigrp router-id command requires an IPv6 address within the router configuration mode.

    The network command is required within the router configuration mode.

    The no shutdown command is required within the router configuration mode.*

    The router eigrp autonomous-system command is required within the router configuration mode.

  3. Fill in the blank.

    In an EIGRP topology table, a route that is in a/an ________ state will cause the Diffusing Update Algorithm to send EIGRP queries that ask other routers for a path to this network.
    Correct Answer: active

  4. Refer to the exhibit. Which two networks contain feasible successors? (Choose two.)

    10.44.100.252*

    10.44.101.252

    192.168.71.0*

    192.168.51.0

    10.44.104.253

  5. Which three metric weights are set to zero by default when costs in EIGRP are being calculated?

    (Choose three.)

    k5*

    k6

    k2*

    k4*

    k3

    k1

  6. Refer to the exhibit. R2 has two possible paths to the 192.168.10.4 network. What would make the alternate route meet the feasibility condition?

    a reported distance less than 3523840*

    a reported distance greater than 41024000

    a feasible distance greater than 41024000

    an administrative distance less than 170

  7. Fill in the Blank. Use the abbreviation.

    EIGRP uses the protocol ______ to deliver EIGRP packets to neighbors.
    Correct Answer: RTP*

  8. What is identified within the opcode of an EIGRP packet header?

    the EIGRP sum of delays from source to destination

    the EIGRP hold timer agreed upon with a neighbor

    the EIGRP message type that is being sent or received from a neighbor*

    the EIGRP autonomous system metrics

  9. Which table is used by EIGRP to store all routes that are learned from EIGRP neighbors?

    the adjacency table

    the routing table

    the topology table*

    the neighbor table

  10. When an EIGRP-enabled router uses a password to accept routes from other EIGRP-enabled routers, which mechanism is used?

    Reliable Transport Protocol

    partial updates

    EIGRP authentication*

    bounded updates

    Diffusing Update Algorithm

  11. Which destination MAC address is used when a multicast EIGRP packet is encapsulated into an Ethernet frame?

    01-00-5E-00-00-09

    01-00-5E-00-00-10

    01-00-5E-00-00-0A*

    01-00-5E-00-00-0B

  12. What is the purpose of using protocol-dependent modules in EIGRP?

    to describe different routing processes

    to identify different application layer protocols

    to accommodate routing of different network layer protocols*

    to use different transport protocols for different packets

  13. If all router Ethernet interfaces in an EIGRP network are configured with the default EIGRP timers, how long will a router wait by default to receive an EIGRP packet from its neighbor before declaring the neighbor unreachable?

    10 seconds

    15 seconds*

    20 seconds

    30 seconds

  14. Which command or commands must be entered on a serial interface of a Cisco router to restore the bandwidth to the default value of that specific router interface?

    shutdown
    no shutdown

    bandwidth 1500

    copy running-config startup-config
    reload

    no bandwidth*

  15. Which two factors does an EIGRP router use to determine that a route to a remote network meets the feasible condition and is therefore loop-free? (Choose two.)

    the feasible distance on the local router*

    the reported distance on a neighbor router*

    the administrative distance on the remote router

    the successor route on a neighbor router

    the feasible successor route on the remote router

  16. Why would a network administrator use a wildcard mask in the network command when configuring a router to use EIGRP?

    to exclude some interfaces from the EIGRP process*

    to send a manual summarization

    to lower the router overhead

    to subnet at the time of the configuration

  17. Refer to the exhibit. R3 has two possible paths to the 172.16.99.0 network. What is the reported distance of the feasible successor route?

    2340608

    2169856

    2816*

    10512128

  18. Which statement describes a characteristic of the delivery of EIGRP update packets?

    EIGRP sends all update packets via multicast.

    EIGRP sends all update packets via unicast.

    EIGRP uses a reliable delivery protocol to send all update packets.*

    EIGRP uses UDP to send all update packets.

  19. An administrator issues the router eigrp 100 command on a router. What is the number 100 used for?

    as the length of time this router will wait to hear hello packets from a neighbor

    as the number of neighbors supported by this router

    as the autonomous system number*

    as the maximum bandwidth of the fastest interface on the router

  20. Which two EIGRP packet types are sent with unreliable delivery? (Choose two.)

    query

    update

    hello*

    acknowledgment*

    reply

  21. A network administrator wants to verify the default delay values for the interfaces on an EIGRP-enabled router. Which command will display these values?

    show running-config

    show ip protocols

    show interfaces*

    show ip route

  22. Open the PT Activity. Perform the tasks in the activity instructions and then answer the question. Which code is displayed on the web server?

    Done

    IPv6EIGRP

    Complete*

    EIGRP

  23. A new network administrator has been asked to verify the metrics that are used by EIGRP on a Cisco device. Which two EIGRP metrics are measured by using static values on a Cisco device? (Choose two.)

    load

    reliability

    bandwidth*

    MTU

    delay*

  24. Question as presented:

  25. Question as presented:

Post Comment