CCNA 3 Scaling Networks Ver 6.0 – ITN Chapter 4 Exam Answers

CCNA 3 Scaling Networks Ver 6.0 – ITN Chapter 4 Exam Answers
Rate this post
  1. What is the purpose of HSRP?

    It provides a continuous network connection when a router fails.*

    It prevents a rogue switch from becoming the STP root.

    It prevents malicious hosts from connecting to trunk ports.

    It enables an access port to immediately transition to the forwarding state.

  2. Refer to the exhibit. An EtherChannel was configured between switches S1 and S2, but the interfaces do not form an EtherChannel. What is the problem?

    The switch ports have to be configured as access ports with each port having a VLAN assigned.

    The interface port-channel number has to be different on each switch.

    The switch ports were not configured with speed and duplex mode.

    The EtherChannel was not configured with the same allowed range of VLANs on each interface.*

  3. Refer to the exhibit. Based on the command output shown, what is the status of the EtherChannel?

    The EtherChannel is dynamic and is using ports Fa0/10 and Fa0/11 as passive ports.

    The EtherChannel is down as evidenced by the protocol field being empty.

    The EtherChannel is partially functional as indicated by the P flags for the FastEthernet ports.

    The EtherChannel is in use and functional as indicated by the SU and P flags in the command output.*

  4. What is a requirement to configure a trunking EtherChannel between two switches?

    The participating interfaces must be assigned the same VLAN number on both switches.

    The participating interfaces must be on the same module on a switch.

    The participating interfaces must be physically contiguous on a switch.

    The allowed range of VLANs must be the same on both switches.*

  5. A network administrator would like to ensure that router R1 is always elected the active router for an HSRP group. Which set of commands would ensure the required results?

    R1(config-if)# ip address 192.168.1.250 255.255.255.0
    R1(config-if)# standby 1 ip 192.168.1.1
    R1(config-if)# no shutdown

    R1(config-if)# ip address 192.168.1.100 255.255.255.0
    R1(config-if)# standby 1 ip 192.168.1.1
    R1(config-if)# standby 1 priority 255
    R1(config-if)# standby 1 preempt
    R1(config-if)# no shutdown*

    R1(config-if)# ip address 192.168.1.100 255.255.255.0
    R1(config-if)# standby 1 ip 192.168.1.1
    R1(config-if)# standby 1 priority 1
    R1(config-if)# no shutdown

    R1(config-if)# ip address 192.168.1.100 255.255.255.0
    R1(config-if)# standby 1 ip 192.168.1.1
    R1(config-if)# standby 1 priority 150
    R1(config-if)# no shutdown

  6. Refer to the exhibit. A network engineer is troubleshooting host connectivity on a LAN that uses a first hop redundancy protocol. Which IPv4 gateway address should be configured on the host?

    192.168.2.0

    192.168.2.1

    192.168.2.2

    192.168.2.100*

  7. What is an advantage of using LACP?

    increases redundancy to Layer 3 devices

    decreases the amount of configuration that is needed on a switch for EtherChannel

    allows automatic formation of EtherChannel links*

    provides a simulated environment for testing link aggregation

    decreases the chance of a spanning-tree loop

  8. Refer to the exhibit. A network administrator configured routers R1 and R2 as part of HSRP group 1. After the routers have been reloaded, a user on Host1 complained of lack of connectivity to the Internet The network administrator issued the show standby briefcommand on both routers to verify the HSRP operations. In addition, the administrator observed the ARP table on Host1. Which entry should be seen in the ARP table on Host1 in order to gain connectivity to the Internet?

    the virtual IP address of the HSRP group 1 and the MAC address of R1

    the virtual IP address of the HSRP group 1 and the MAC address of R2

    the virtual IP address and the virtual MAC address for the HSRP group 1*

    the IP address and the MAC address of R1

  9. Fill in the blank.

    In FHRP operation, two or more routers are represented as a single ________ router.
    Correct Answer: virtual*

  10. What is a best practice to use before beginning an EtherChannel implementation?

    Enable each of the affected interfaces.

    Assign affected interfaces to the management VLAN.

    Shut down each of the affected interfaces.*

    Assign affected interfaces to VLAN 1.

    Assign affected interfaces to an unused VLAN.

  11. Which statement describes an EtherChannel implementation?

    EtherChannel operates only at Layer 2.

    A trunked port can be part of an EtherChannel bundle.*

    EtherChannel can support up to a maximum of ten separate links.

    PAgP cannot be used in conjunction with EtherChannel.

  12. Open the PT Activity. Perform the tasks in the activity instructions and then answer the question. What are two reasons why the ping messages that are issued from Laptop0 towards Laptop1 are failing? (Choose two.)

    The two interfaces on each of the switches belong to different VLANs.*

    The interface VLAN 1 is shut down on both switches.

    The channel group mode is not set correctly on the switches.

    The wrong cable types are connecting the two switches.

    The channel group should be configured as a trunk on each switch.*

  13. Refer to the exhibit. A network administrator issued the show etherchannel summarycommand on the switch S1. What conclusion can be drawn?

    The EtherChannel is not functional.*

    The EtherChannel is suspended.

    FastEthernet ports Fa0/1, Fa0/2, and Fa0/3 do not join the EtherChannel.

    The port aggregation protocol PAgP is misconfigured.

  14. Which PAgP mode combination will establish an EtherChannel?

    switch 1 set to desirable; switch 2 set to desirable.*

    switch 1 set to auto; switch 2 set to auto.

    switch 1 set to on; switch 2 set to desirable.

    switch 1 set to auto; switch 2 set to on.

  15. Refer to the exhibit. What statement is true about the output of the show standby command?

    The current priority of this router is 120.

    This router is tracking two properly operating interfaces.

    This router is in the HSRP down state because its tracked interfaces are down.

    The router is currently forwarding packets.*

  16. Which three options must match in order to establish an EtherChannel between two directly connected switches?

    (Choose three.)

    duplex settings of the interfaces that are used for EtherChannel*

    port security settings on the interfaces that used for EtherChannel

    VLAN memberships of the interfaces that are used for EtherChannel*

    speed of the interfaces that are used for EtherChannel*

    domain names on the switches

    port numbers that are used for the EtherChannel

  17. Which two protocols are used to implement EtherChannel? (Choose two.)

    Link Aggregation Control Protocol*

    Spanning Tree Protocol

    Port Aggregation Protocol*

    Cisco Discovery Protocol

    Rapid Spanning Tree Protocol

  18. Which command must be used on SW2 to enable this EtherChannel?

    SW2(config-if-range)# channel-group 1 mode desirable*

    SW2(config-if-range)# channel-group 1 mode auto

    SW2(config-if-range)# channel-group 1 mode passive

    SW2(config-if-range)# channel-group 1 mode active

  19. An EtherChannel link using LACP was formed between two switches, S1 and S2. While verifying the configuration, which mode combination could be utilized on both switches?

    S1-on and S2-active

    S1-passive and S2-passive

    S1-on and S2-passive

    S1-passive and S2-active*

  20. Which statement describes a characteristic of EtherChannel?

    It can bundle mixed types of 100 Mb/s and 1Gb/s Ethernet links.

    It consists of multiple parallel links between a switch and a router.

    It can combine up to a maximum of 4 physical links.

    It is made by combining multiple physical links that are seen as one link between two switches.*

  21. Refer to the exhibit. Which switching technology would allow each access layer switch link to be aggregated to provide more bandwidth between each Layer 2 switch and the Layer 3 switch?

    HSRP

    EtherChannel*

    trunking

    PortFast

  22. Which statement is true regarding the use of PAgP to create EtherChannels?

    It requires more physical links than LACP does.

    It mandates that an even number of ports (2, 4, 6, etc.) be used for aggregation.

    It is Cisco proprietary.*

    It increases the number of ports that are participating in spanning tree.

    It requires full duplex.

  23. Refer to the exhibit. A network administrator has decided that an EtherChannel between ports 0/1 and 0/2 on switches S1 and S2 would help performance. After making the configuration, the administrator notices no performance gain. Based on the output that is shown, what two possible assumptions could a network administrator make? (Choose two.)

    Switch S2 did not use a compatible EtherChannel mode.

    The EtherChannel bundle is working.

    One of the ports on S2 was not configured correctly.*

    LACP and PAgP were both used to form the EtherChannel.

    The EtherChannel bundle is not working.*

    Switch S2 must be configured so that the maximum number of port channels is increased.

  24. Which nonproprietary protocol provides router redundancy for a group of routers which support IPv4 LANs?

    GLBP

    SLB

    VRRPv2*

    HSRP

  25. A network administrator is configuring an EtherChannel link between switches SW1 and SW2 by using the command SW1(config-if-range)# channel-group 1 mode passive. Which command must be used on SW2 to enable this EtherChannel?

    SW2(config-if-range)# channel-group 1 mode desirable

    SW2(config-if-range)# channel-group 1 mode auto

    SW2(config-if-range)# channel-group 1 mode passive

    SW2(config-if-range)# channel-group 1 mode active*

  26. Question as presented:

Post Comment