Home / CCNA V6.0 / CCNA 3 / CCNA 3 Scaling Networks Ver 6.0 – ITN Chapter 2 Exam Answers

CCNA 3 Scaling Networks Ver 6.0 – ITN Chapter 2 Exam Answers

  1. Refer to the exhibit. A network engineer is troubleshooting host connectivity on a LAN that uses a first hop redundancy protocol. Which IPv4 gateway address should be configured on the host?

    CCNA3_Ch3_02

    • 192.168.2.0
    • 192.168.2.1
    • 192.168.2.2
    • 192.168.2.100*
  2. Fill in the blank. Do not use abbreviations.

    The spanning-tree mode rapid-pvst global configuration command is used to enable Rapid PVST+

  3. Fill in the blank.

    In FHRP operation, two or more routers are represented as a single virtualrouter.

  4. What could be the effect of duplicate unicast frames arriving at a destination device due to multiple active alternative physical paths?

    • Frame collisions increase.
    • The number of broadcast domains increases.
    • Application protocols malfunction.*
    • The number of collision domains increases.
  5. Refer to the exhibit. Which trunk link will not forward any traffic after the root bridge election process is complete?

    CCNA3 Chapter 2 v5.03 004

    CCNA3 Chapter 2 v5.03 004
    • Trunk1
    • Trunk2*
    • Trunk3
    • Trunk4
  6. Which STP port role is adopted by a switch port if there is no other port with a lower cost to the root bridge?

    • designated port
    • root port*
    • alternate
    • disabled port
  7. Which is the default STP operation mode on Cisco Catalyst switches?

    • RSTP
    • PVST+*
    • MST
    • MSTP
    • Rapid PVST+
  8. Which two network design features require Spanning Tree Protocol (STP) to ensure correct network operation? (Choose two.)

    • static default routes
    • implementing VLANs to contain broadcasts
    • redundant links between Layer 2 switches*
    • link-state dynamic routing that provides redundant routes
    • removing single points of failure with multiple Layer 2 switches*
  9. What is a characteristic of a Layer 2 loop?

    • Broadcast frames are forwarded back to the sending switch.*
    • The Time-to-Live attribute of a frame is set to infinity.
    • Routers continually forward packets to other routers.
    • A switch is continually forwarding the same unicast frame.
  10. What is the outcome of a Layer 2 broadcast storm?

    • Routers will take over the forwarding of frames as switches become congested.
    • New traffic is discarded by the switch because it is unable to be processed.*
    • CSMA/CD will cause each host to continue transmitting frames.
    • ARP broadcast requests are returned to the transmitting host.
  11. What additional information is contained in the 12-bit extended system ID of a BPDU?

    • MAC address
    • VLAN ID*
    • IP address
    • port ID
  12. Which three components are combined to form a bridge ID?

    • port ID
    • IP address
    • extended system ID*
    • MAC address *
    • bridge priority*
    • cost
  13. Which STP priority configuration would ensure that a switch would always be the root switch?

    • spanning-tree vlan 10 priority 0*
    • spanning-tree vlan 10 priority 61440
    • spanning-tree vlan 10 root primary
    • spanning-tree vlan 10 priority 4096
  14. Which protocol provides up to 16 instances of RSTP, combines many VLANs with the same physical and logical topology into a common RSTP instance, and provides support for PortFast, BPDU guard, BPDU filter, root guard, and loop guard?

    • STP
    • Rapid PVST+
    • PVST+
    • MST*
  15. Which two types of spanning tree protocols can cause suboptimal traffic flows because they assume only one spanning-tree instance for the entire bridged network? (Choose two.)

    • STP*
    • Rapid PVST+
    • PVST+
    • MSTP
    • RSTP*
  16. What is an advantage of PVST+?

    • PVST+ requires fewer CPU cycles for all the switches in the network.
    • PVST+ reduces bandwidth consumption compared to traditional implementations of STP that use CST.
    • PVST+ optimizes performance on the network through autoselection of the root bridge.
    • PVST+ optimizes performance on the network through load sharing.*
  17. In which two port states does a switch learn MAC addresses and process BPDUs in a PVST network? (Choose two.)

    • blocking
    • disabled
    • forwarding *
    • learning*
    • listening
  18. If no bridge priority is configured in PVST, which criteria is considered when electing the root bridge?

    • lowest IP address
    • lowest MAC address*
    • highest IP address
    • highest MAC address
  19. Which RSTP ports are connected to end devices?

    • trunk ports
    • designated ports
    • root ports
    • edge ports*
  20. A network administrator is preparing the implementation of Rapid PVST+ on a production network. How are the Rapid PVST+ link types determined on the switch interfaces?

    • Link types are determined automatically.*
    • Link types must be configured with specific port configuration commands.
    • Link types can only be determined if PortFast has been configured.
    • Link types can only be configured on access ports configured with a single VLAN.
  21. Which port state will switch ports immediately transition to when configured for PortFast?

    • listening
    • learning
    • forwarding*
    • blocking
  22. To obtain an overview of the spanning tree status of a switched network, a network engineer issues the show spanning-tree command on a switch. Which two items of information will this command display? (Choose two.)

    • The root bridge BID.*
    • The role of the ports in all VLANs.*
    • The status of native VLAN ports.
    • The number of broadcasts received on each root port.
    • The IP address of the management VLAN interface.
  23. What is the purpose of HSRP?

    • It provides a continuous network connection when a router fails.*
    • It prevents a rogue switch from becoming the STP root.
    • It enables an access port to immediately transition to the forwarding state.
    • It prevents malicious hosts from connecting to trunk ports.
  24. Which nonproprietary protocol provides router redundancy for a group of routers which support IPv4 LANs?

    • HSRP
    • VRRPv2 *
    • GLBP
    • SLB
  25. Refer to the exhibit. Which protocol information is being displayed in the output?CCNA3_Ch3_01

    • FHRP
    • GLBP*
    • HSRP
    • VRRP
  26. What value determines the root bridge when all switches connected by trunk links have default STP configurations?

    • VLAN ID
    • MAC address*
    • extended system ID
    • bridge priority
  27. Which two concepts relate to a switch port that is intended to have only end devices attached and intended never to be used to connect to another switch? (Choose two.)

    • bridge ID
    • edge port*
    • extended system ID
    • PortFast*
    • PVST+
  28. Which Cisco switch feature ensures that configured switch edge ports do not cause Layer 2 loops if a port is mistakenly connected to another switch?

    • BPDU guard*
    • extended system ID
    • PortFast
    • PVST+
  29. Refer to the exhibit. A network administrator configured routers R1 and R2 as part of HSRP group 1. After the routers have been reloaded, a user on Host1 complained of lack of connectivity to the Internet The network administrator issued the show standby brief command on both routers to verify the HSRP operations. In addition, the administrator observed the ARP table on Host1. Which entry should be seen in the ARP table on Host1 in order to gain connectivity to the Internet?

    CCNA3 Chapter 2 v5.03 003

    CCNA3 Chapter 2 v5.03 003
    • the IP address and the MAC address of R1
    • the virtual IP address and the virtual MAC address for the HSRP group 1*
    • the virtual IP address of the HSRP group 1 and the MAC address of R1
    • the virtual IP address of the HSRP group 1 and the MAC address of R2
  30. Fill in the blank. Do not abbreviate.

    To enable Rapid PVST+ on a Cisco switch, the spanning-tree mode rapid-pvst global configuration mode command is required

  31. Fill in the blank. Use a number.

    The default hello timer value for STP BPDU frames is 2 seconds.

Launch PT. Hide and Save PT

Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
Which switch is the root bridge?​

Switch_1

Switch_2

Switch_4*

Switch_3

32. Match the step number to the sequence of stages that occur during the HSRP failover process.

Place the options in the following order:

The new forwarding router assumes both the IP and MAC address of the virtual router. -> Step 4
– not scored –
The standby router assumes the role of the forwarding router. -> Step 3
The forwarding router fails. -> Step 1
The standby router stops seeing hello messages from the forwarding router. -> Step 2

33. Match the spanning-tree feature with the protocol type. (Not all options are used.)

Place the options in the following order:

Cisco implementation of IEEE 802.1D ======> PVST+

Fast converging enhancement of IEEE 802.1D ======> RSTP

IEEE standard that reduces the number of STP instances ======+> MSTP

– not scored – =================> MST

Proprietary per VLAN implementation of IEEE 802.1w =====> Rapid PVST+

Check Also

CCNA 4 Routing & Switching Essentials Ver 6.0 – ITN Final Exam Answers

Refer to the exhibit. The inside local IP address of PC-A is 192.168.0.200. What will …

Leave a Reply

Your email address will not be published. Required fields are marked *