CCNA Discovery 4 Chapter 3 Answers

CCNA Exploration 4 Chapter 3 Exam Answers

1.

CCNAExploration4Chapter3ExamAnswers thumb CCNA Exploration 4 Chapter 3 Exam Answers

Refer to the exhibit. What can be determined about the configuration of router R1 from the exhibited output?

LMI updates are not being received properly.

The LMI type for the Serial 0/0/0 interface has been left to its default configuration.

Cisco HDLC is used as a Layer 2 encapsulation protocol on the Serial 0/0/0 interface.

The Serial 0/0/0 interface has been configured as a data communications equipment device.

 

2. What two methods does Frame Relay technology use to process frames that contain errors? (Choose two.)

Frame Relay services depend on the upper layer protocols to handle error recovery.

It requires the receiving device to request that the sender retransmit erroneous frames.

FECN, BECN, and DE bits are set in the frames to minimize errors.

The receiving device drops any frames that contain errors without notifying the sender.

The frame relay switch notifies the sender that errors were detected.

 

3. Which Frame Relay topology is a compromise of costs, reliability, and complexity when the WAN contains one headquarters site, 40 regional sites, and several sites within each regional site?

star

full mesh

partial mesh

point-to-multipoint

point-to-point

(more…)

Tags: A DHCP server is configured with a block of excluded addresses What two devices would be assigned static addresses from the excluded address range? (Choose two ), refer to the exhibit which statement is true about frame relay traffic on r1?, Which three actions might a Frame Relay switch perform when it detects an excessive build-up of frames in its queue? (Choose three ), Refer to the exhibit Frame Relay connectivity has been configured in the network and OSPF is used as the routing protocol Router R1 can successfully ping the router R2 serial interface When R1 attempts to ping network 192 168 3 0/24 the ping fails What ad, Refer to the exhibit What can be determined from the exhibited output?, ccna exploration 3 chapter 3 exam answers, CCNA Exploration 4 Chapter 3 Exam Answers, ccna 4 chapter 3, Which Frame Relay topology is a compromise of costs reliability and complexity when the WAN contains one headquarters site 40 regional sites and several sites within each regional site?, ccna exploration 4 final exam answers, which statement is true about frame relay traffic on r1, which statement is true about frame relay traffic on r1?, Which best describes the benefit of using Frame Relay as opposed to a leased line or ISDN service?, Refer to the exhibit A network administrator is tasked with completing the Frame Relay topology that interconnects two remote sites How should the point-to-point subinterfaces be configured on HQ to complete the topology?, Refer to the exhibit You are a network administrator who has been tasked with completing the Frame Relay topology that interconnects two remote sites Router HQ belongs to both the 172 16 1 0/24 and 172 16 2 0/24 subnets with IP addresses of 172 16 1 3 and, ccna exploration 4 chapter 3, ccna exploration 4 chapter 3 answers, Which statement about Frame Relay subinterfaces is correct?, Which three actions might a Frame Relay switch perform when it detects an excessive build-up of frames in its queue?, Refer to the exhibit Which statement is true about the status of the Frame Relay connection?, What is created between two DTEs in a Frame Relay network?, Refer to the exhibit Which statement is true about the Frame Relay connection?, Refer to the exhibit What can be determined from the exhibited output, CCNA Exploration 4 0 answers, Which best describes the benefit of using Frame Relay as opposed to a leased line or ISDN service, Refer to the exhibit What can be determined about the configuration of router R1 from the exhibited output?, ccna 4 chapter 3 exam answers, Refer to the exhibit Router R1 has been configured for Frame Relay connectivity to routers R2 and R3 What configuration option should be configured on the R2 and R3 serial interfaces in order for all routers to ping each other successfully?, What best describes the use of a data-link connection identifier (DLCI)?, What two methods does Frame Relay technology use to process frames that contain errors? (Choose two ), Refer to the exhibit What can be known about the configuration of router R1 from the output?, Refer to the exhibit You are a network administrator who has been tasked with completing the Frame Relay topology that interconnects two remote sites How should the point-to-point subinterfaces be configured on HQ to complete the topology?, Refer to the exhibit A ping is sent to address 192 168 50 10 from the Peanut router Which DLCI will be used to send the ping?, ccna exploration 4, ccna exploration 4 0 chapter 3 answers, Refer to the exhibit What can be determined about the Frame Relay switch from the output shown?, Which three actions might a Frame Relay switch perform when it detects an excessive build-up of frames in its queue, Frame Relay connectivity has been configured in the network and OSPF is used as the routing protocol Router R1 can successfully ping the router R2 serial interface When R1 attempts to ping network 192 168 3 0/24 the ping fails What additional configuratio, ccna chapter 3 exam answers, Refer to the exhibit Which statement explains why the Frame Relay connection between R1 and R2 is failing?, exploration 4 chapter 3, Refer to the exhibit Router R1 has been configured for Frame Relay connectivity to routers R2 and R3 Which set of configuration options for routers R2 and R3 would provide each router connectivity to R1?, ccna chapter 3, Refer to the exhibit What effect does the point-to-point configuration on subinterface S0/0 110 have on the operation of the router?, ccna exploration 3 answers, What is created between two DTEs in a Frame Relay network, ccna exploration chapter 3 answers, ccna 4 chapter 3 exam, What can be determined from the exhibited output?, ccna chapter 3 exam